Astm d2794

Precision and Bias After the coatings have cured, a standard weight is dropped a distance to strike an indenter that deforms the coating and the substrate. Summary of Test Method 4. Graduations are marked in inch-pounds along the slot.

Uploader: Kaktilar
Date Added: 28 November 2010
File Size: 28.43 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 43353
Price: Free* [*Free Regsitration Required]





The indentation can be either an intrusion or an extrusion.

The indentation can be either an intrusion or an extrusion. Raise the weight up the tube asym a height where it is expected that no failure will occur. Historical Version s - view previous versions of standard.

ASTM D - Zehntner GmbH

As coatings such as paint, d794, conversion coatings, and related coating products are subjected to impact damage during their manufacturing and useful life, this test method for impact resistance has been found to be useful in predicting coating resistance to impact.

A number in parentheses indicates the year of last reapproval. By gradually increasing the distance the weight drops, generally 1 inch 25 mm at a time, the point at which failure usually occurs can be determined.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Universal Impact Testing – ASTM D2794

Once visible cracks are observed, repeat the asym Link to Active This link will always route to the current Active version of the standard. NOTE 4—Because of the poor reproducibility of this method, the reporting of inch-pounds kilogram-metres in comparing coatings for impact resistance should be restricted to one laboratory. We also built a six-foot tall tester for custom testing.

ASTM_D(Impact)_百度文库

Coatings attached to substrates are subjected to damaging impacts during the manufacture of articles and their use in service.

Interlaboratory agreement is improved when ranking is used in place atm numerical values. Place the test panel in the apparatus with the coated side either up or down as speci?

Films generally fail by cracking, which is made more visible by the use of a magni? NOTE 1—The coatings should be applied in accordance with Practices Dor as agreed upon between the producer and the user. A slot is cut lengthwise on one side of the tube to act as a guide for awtm cylindrical weight that?

Moisten the probe sponge with tap water and slowly draw the probe over the impact area. We have two impact testers to evaluate a aastm and sizes of materials — a tabletop tester shown on the left, and a foot tall model. Last previous edition approved in awtm D — 93 e1.

Lightly place the weight on the indenter and adjust the guide tube so that the lifting pin is at the zero mark.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Touchstone offers various kinds of impact testing including Charpy and Izod impact testing and micro-scale impact tests performed inside a scanning electron microscope.

This standard is ashm to revision at any time by the responsible technical committee and must be reviewed every? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard ASTM D2794

Conduct asfm test in the same environment or immediately on removal therefrom. Prepare a minimum of four coated panels for the material. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

The base is constructed so that a thin? Originally approved in Precision and Bias NOTE 3—The copper sulfate solution will not perform asmt on zinc-phosphate-treated metal unless the conversion coating cracks.

Once visible cracks have been identified, the test is satm five times at that level, as well as five times above f2794 below that level. Interlaboratory agreement is improved when ranking is used in place of numerical values. The value where the results change from mainly passing to mainly failing is the impact failure end point. Of course, these confirmation tests are conducted in a random order so successive tests are not conducted at the same height or on the same panel.

This entry was posted in Ebook. Bookmark the permalink.

5 Responses to Astm d2794

  1. Tojakasa says:

    I consider, that you commit an error. Write to me in PM, we will discuss.

  2. Sak says:

    It seems brilliant idea to me is

  3. Vozshura says:

    I think, that you are mistaken. Write to me in PM, we will discuss.

  4. Voodootilar says:

    Idea good, it agree with you.

  5. Volkis says:

    It is remarkable, this valuable opinion

Leave a Reply

Your email address will not be published. Required fields are marked *